Sale!

SCHNEIDER ELECTRIC TELEMECANIQUE SQUARE D 10 HP 480 VOLT AC DRIVE ATV32HU75N4

Original price was: $ 1,890.00.Current price is: $ 1,700.99.

Model: ATV32HU75N4
Category:

Description

Model: ATV32HU75N4
Main
range of product
Altivar 32
product or component type
Variable speed drive
product destination
Asynchronous motors
Synchronous motors
product specific application
Complex machines
function available
assembly style
With heat sink
component name
ATV32
EMC filter
Class C2 EMC filter integrated
network number of phases
3 phases
[Us] rated supply voltage
380…500 V – 15…10 %
supply voltage limits
323…550 V
supply frequency
50…60 Hz – 5…5 %
network frequency
47.5…63 Hz
motor power kW
7.5 kW at 380…480 V
motor power hp
10 hp at 380…480 V
Complementary
line current
18.7 A for 500 V 3 phases 7.5 kW / 10 hp
26.5 A for 380 V 3 phases 7.5 kW / 10 hp
apparent power
22.9 kVA at 500 V 3 phases 7.5 kW / 15 hp
prospective line Isc
22 kA for 3 phases
nominal output current
17 A at 4 kHz 500 V 7.5 kW / 10 hp
maximum transient current
25.5 A for 60 s 7.5 kW / 10 hp
Output frequency
0.0005…0.599 kHz
nominal switching frequency
4 kHz
switching frequency
2…16 kHz adjustable
speed range
1…100 for asynchronous motor in open-loop mode
speed accuracy
+/- 10 % of nominal slip 0.2 Tn to Tn
torque accuracy
+/- 15 %
transient overtorque
170…200 %
braking torque
<= 170 % with braking resistor
asynchronous motor control profile
Flux vector control without sensor, standard
Voltage/frequency ratio, 2 points
Flux vector control without sensor – Energy Saving, NoLoad law
Voltage/frequency ratio, 5 points
Voltage/frequency ratio – Energy Saving, quadratic U/f
synchronous motor control profile
Vector control without sensor
regulation loop
Adjustable PID regulator
motor slip compensation
Not available in voltage/frequency ratio (2 or 5 points)
Adjustable 0…300 %
Automatic whatever the load
local signalling
1 LED red for drive voltage
1 LED green for CANopen run
1 LED red for CANopen error
1 LED red for drive fault
output voltage
<= power supply voltage
noise level
43 dB conforming to 86/188/EEC
insulation
Electrical between power and control
electrical connection
Screw terminal, clamping capacity: 0.5…1.5 mm², AWG 18…AWG 14 (control)
Removable screw terminals, clamping capacity: 2.5…16 mm², AWG 12…AWG 6 (motor/braking resistor)
Screw terminal, clamping capacity: 6…16 mm², AWG 8…AWG 6 (power supply)
tightening torque
0.5 N.m, 4.4 lb/ft (control)
1.2 N.m, 10.6 lb/ft (motor/braking resistor)
1.2 N.m, 10.6 lb/ft (power supply)
supply
Internal supply for reference potentiometer (1 to 10 kOhm): 10.5 V DC +/- 5 %, <10 mA, protection type: overload and short-circuit protection
analogue input number
3
analogue input type
AI1 voltage: 0…10 V DC, impedance: 30000 Ohm, resolution 10 bits
AI2 bipolar differential voltage: +/- 10 V DC, impedance: 30000 Ohm, resolution 10 bits
AI3 current: 0…20 mA (or 4-20 mA, x-20 mA, 20-x mA or other patterns by configuration), impedance: 250 Ohm, resolution 10 bits
sampling duration
2 ms (AI1, AI2, AI3) – analog input(s)
2 ms (AO1) – analog input(s)
response time
LI1…LI6 8 ms, tolerance +/- 0.7 ms for logic output(s)
R1A, R1B, R1C 2 ms for relay output(s)
R2A, R2C 2 ms for relay output(s)
accuracy
+/- 0.2 % (AI1, AI2, AI3) for a temperature of -10…60 °C
+/- 0.5 % (AI1, AI2, AI3) for a temperature of 25 °C
+/- 1 % (AO1) for a temperature of 25 °C
+/- 2 % (AO1) for a temperature of -10…60 °C
linearity error
+/- 0.2…0.5 % of maximum value (AI1, AI2, AI3)
+/- 0.3 % (AO1)
analogue output number
1
analogue output type
AO1 software-configurable current 0…20 mA, impedance: 800 Ohm, resolution 10 bits
AO1 software-configurable voltage 0…10 V, impedance: 470 Ohm, resolution 10 bits
discrete output number
3
discrete output type
Configurable relay logic: (R1A, R1B, R1C) NO/NC – 100000 cycles
Configurable relay logic: (R2A, R2B) NO – 100000 cycles
Logic: (LO)
minimum switching current
5 mA at 24 V DC for configurable relay logic
maximum switching current
R1: 3 A at 250 V AC resistive load, cos phi = 1
R1: 4 A at 30 V DC resistive load, cos phi = 1
R1, R2: 2 A at 250 V AC inductive load, cos phi = 0.4
R1, R2: 2 A at 30 V DC inductive load, cos phi = 0.4
R2: 5 A at 250 V AC resistive load, cos phi = 1
R2: 5 A at 30 V DC resistive load, cos phi = 1
discrete input number
7
discrete input type
Programmable (sink/source) (LI1…LI4)24…30 V DC, with level 1 PLC
Programmable as pulse input 20 kpps (LI5)24…30 V DC, with level 1 PLC
Switch-configurable PTC probe (LI6)24…30 V DC
Safe torque off (STO)24…30 V DC – 1500 Ohm
discrete input logic
Negative logic (sink) (LI1…LI6), > 19 V (state 0), < 13 V (state 1)
Positive logic (source) (LI1…LI6), < 5 V (state 0), > 11 V (state 1)
acceleration and deceleration ramps
Deceleration ramp automatic stop DC injection
S
Linear
Ramp switching
U
CUS
Deceleration ramp adaptation
braking to standstill
By DC injection
protection type
Input phase breaks: drive
Overcurrent between output phases and earth: drive
Overheating protection: drive
Short-circuit between motor phases: drive
Thermal protection: drive
communication port protocol
CANopen
Modbus
connector type
1 RJ45 (on front face) for Modbus/CANopen
physical interface
2-wire RS 485 for Modbus
transmission frame
RTU for Modbus
type of polarization
No impedance for Modbus
number of addresses
1…127 for CANopen
1…247 for Modbus
method of access
Slave CANopen
electromagnetic compatibility
1.2/50 µs – 8/20 µs surge immunity test, level 3 conforming to IEC 61000-4-5
Conducted radio-frequency immunity test, level 3 conforming to IEC 61000-4-6
Electrical fast transient/burst immunity test, level 4 conforming to IEC 61000-4-4
Electrostatic discharge immunity test, level 3 conforming to IEC 61000-4-2
Radiated radio-frequency electromagnetic field immunity test, level 3 conforming to IEC 61000-4-3
Voltage dips and interruptions immunity test conforming to IEC 61000-4-11
width
150 mm
height
308 mm
depth
232 mm
net weight
7.5 kg
option card
Communication card for CANopen daisy chain
Communication card for CANopen open style
Communication card for DeviceNet
Communication card for Ethernet/IP
Communication card for Profibus DP V1
functionality
Mid
specific application
Other applications
Environment
standards
EN 61800-3 environments 2 category C2
EN/IEC 61800-3
EN/IEC 61800-5-1
EN 61800-3 environments 1 category C2
EN 55011 class A group 1
product certifications
NOM 117
GOST
C-Tick
UL
CSA
marking
CE
pollution degree
2 conforming to EN/IEC 61800-5-1
IP degree of protection
IP20 conforming to EN/IEC 61800-5-1
vibration resistance
1 gn (f = 13…200 Hz) conforming to EN/IEC 60068-2-6
1.5 mm peak to peak (f = 3…13 Hz) conforming to EN/IEC 60068-2-6
shock resistance
15 gn for 11 ms conforming to EN/IEC 60068-2-27
relative humidity
5…95 % without condensation conforming to IEC 60068-2-3
5…95 % without dripping water conforming to IEC 60068-2-3
ambient air temperature for operation
-10…50 °C without derating
50…60 °C with derating factor
ambient air temperature for storage
-25…70 °C
operating altitude
<= 1000 m without derating
1000…3000 m with current derating 1 % per 100 m
operating position
Vertical +/- 10 degree
Packing Units
Package 1 Weight
5.604 kg
Package 1 Height
2.050 dm
Package 1 width
2.700 dm
Package 1 Length
3.300 dm
Contractual warranty
Warranty
18 months