SCHNEIDER ELECTRIC TELEMECANIQUE SQUARE D 10 HP 480 VOLT AC DRIVE ATV32HU75N4

Altivar 32

Variable speed drive

Asynchronous motors
Synchronous motors

Complex machines

–

With heat sink

ATV32

Class C2 EMC filter integrated

3 phases

380…500 V – 15…10 %

323…550 V

50…60 Hz – 5…5 %

47.5…63 Hz

7.5 kW at 380…480 V

10 hp at 380…480 V

18.7 A for 500 V 3 phases 7.5 kW / 10 hp
26.5 A for 380 V 3 phases 7.5 kW / 10 hp

22.9 kVA at 500 V 3 phases 7.5 kW / 15 hp

22 kA for 3 phases

17 A at 4 kHz 500 V 7.5 kW / 10 hp

25.5 A for 60 s 7.5 kW / 10 hp

0.0005…0.599 kHz

4 kHz

2…16 kHz adjustable

1…100 for asynchronous motor in open-loop mode

+/- 10 % of nominal slip 0.2 Tn to Tn

+/- 15 %

170…200 %

<= 170 % with braking resistor

Flux vector control without sensor, standard
Voltage/frequency ratio, 2 points
Flux vector control without sensor – Energy Saving, NoLoad law
Voltage/frequency ratio, 5 points
Voltage/frequency ratio – Energy Saving, quadratic U/f

Vector control without sensor

Adjustable PID regulator

Not available in voltage/frequency ratio (2 or 5 points)
Adjustable 0…300 %
Automatic whatever the load

1 LED red for drive voltage
1 LED green for CANopen run
1 LED red for CANopen error
1 LED red for drive fault

<= power supply voltage

43 dB conforming to 86/188/EEC

Electrical between power and control

Screw terminal, clamping capacity: 0.5…1.5 mm², AWG 18…AWG 14 (control)
Removable screw terminals, clamping capacity: 2.5…16 mm², AWG 12…AWG 6 (motor/braking resistor)
Screw terminal, clamping capacity: 6…16 mm², AWG 8…AWG 6 (power supply)

0.5 N.m, 4.4 lb/ft (control)
1.2 N.m, 10.6 lb/ft (motor/braking resistor)
1.2 N.m, 10.6 lb/ft (power supply)

Internal supply for reference potentiometer (1 to 10 kOhm): 10.5 V DC +/- 5 %, <10 mA, protection type: overload and short-circuit protection

3

AI1 voltage: 0…10 V DC, impedance: 30000 Ohm, resolution 10 bits
AI2 bipolar differential voltage: +/- 10 V DC, impedance: 30000 Ohm, resolution 10 bits
AI3 current: 0…20 mA (or 4-20 mA, x-20 mA, 20-x mA or other patterns by configuration), impedance: 250 Ohm, resolution 10 bits

2 ms (AI1, AI2, AI3) – analog input(s)
2 ms (AO1) – analog input(s)

LI1…LI6 8 ms, tolerance +/- 0.7 ms for logic output(s)
R1A, R1B, R1C 2 ms for relay output(s)
R2A, R2C 2 ms for relay output(s)

+/- 0.2 % (AI1, AI2, AI3) for a temperature of -10…60 °C
+/- 0.5 % (AI1, AI2, AI3) for a temperature of 25 °C
+/- 1 % (AO1) for a temperature of 25 °C
+/- 2 % (AO1) for a temperature of -10…60 °C

+/- 0.2…0.5 % of maximum value (AI1, AI2, AI3)
+/- 0.3 % (AO1)

1

AO1 software-configurable current 0…20 mA, impedance: 800 Ohm, resolution 10 bits
AO1 software-configurable voltage 0…10 V, impedance: 470 Ohm, resolution 10 bits

3

Configurable relay logic: (R1A, R1B, R1C) NO/NC – 100000 cycles
Configurable relay logic: (R2A, R2B) NO – 100000 cycles
Logic: (LO)

5 mA at 24 V DC for configurable relay logic

R1: 3 A at 250 V AC resistive load, cos phi = 1
R1: 4 A at 30 V DC resistive load, cos phi = 1
R1, R2: 2 A at 250 V AC inductive load, cos phi = 0.4
R1, R2: 2 A at 30 V DC inductive load, cos phi = 0.4
R2: 5 A at 250 V AC resistive load, cos phi = 1
R2: 5 A at 30 V DC resistive load, cos phi = 1

7

Programmable (sink/source) (LI1…LI4)24…30 V DC, with level 1 PLC
Programmable as pulse input 20 kpps (LI5)24…30 V DC, with level 1 PLC
Switch-configurable PTC probe (LI6)24…30 V DC
Safe torque off (STO)24…30 V DC – 1500 Ohm

Negative logic (sink) (LI1…LI6), > 19 V (state 0), < 13 V (state 1)
Positive logic (source) (LI1…LI6), < 5 V (state 0), > 11 V (state 1)

Deceleration ramp automatic stop DC injection
S
Linear
Ramp switching
U
CUS
Deceleration ramp adaptation

By DC injection

Input phase breaks: drive
Overcurrent between output phases and earth: drive
Overheating protection: drive
Short-circuit between motor phases: drive
Thermal protection: drive

CANopen
Modbus

1 RJ45 (on front face) for Modbus/CANopen

2-wire RS 485 for Modbus

RTU for Modbus

No impedance for Modbus

1…127 for CANopen
1…247 for Modbus

Slave CANopen

1.2/50 µs – 8/20 µs surge immunity test, level 3 conforming to IEC 61000-4-5
Conducted radio-frequency immunity test, level 3 conforming to IEC 61000-4-6
Electrical fast transient/burst immunity test, level 4 conforming to IEC 61000-4-4
Electrostatic discharge immunity test, level 3 conforming to IEC 61000-4-2
Radiated radio-frequency electromagnetic field immunity test, level 3 conforming to IEC 61000-4-3
Voltage dips and interruptions immunity test conforming to IEC 61000-4-11

150 mm

308 mm

232 mm

7.5 kg

Communication card for CANopen daisy chain
Communication card for CANopen open style
Communication card for DeviceNet
Communication card for Ethernet/IP
Communication card for Profibus DP V1

Mid

Other applications

EN 61800-3 environments 2 category C2
EN/IEC 61800-3
EN/IEC 61800-5-1
EN 61800-3 environments 1 category C2
EN 55011 class A group 1

NOM 117
GOST
C-Tick
UL
CSA

CE

2 conforming to EN/IEC 61800-5-1

IP20 conforming to EN/IEC 61800-5-1

1 gn (f = 13…200 Hz) conforming to EN/IEC 60068-2-6
1.5 mm peak to peak (f = 3…13 Hz) conforming to EN/IEC 60068-2-6

15 gn for 11 ms conforming to EN/IEC 60068-2-27

5…95 % without condensation conforming to IEC 60068-2-3
5…95 % without dripping water conforming to IEC 60068-2-3

-10…50 °C without derating
50…60 °C with derating factor

-25…70 °C

<= 1000 m without derating
1000…3000 m with current derating 1 % per 100 m

Vertical +/- 10 degree

5.604 kg

2.050 dm

2.700 dm

3.300 dm

18 months